Prezentare generala Amplificator casti NuForce HA-200 Negru
The Class-A topology is widely recognized as being the purest form of amplification, and this is because other topologies such as Class B and Class-AB require that two output devices be operated in "push–pull" fashion in order for each to handle one half of the musical waveform. At the point where a given device "hands off" to its opposing counterpart, it must "turn off" or stop conducting current until the waveform polarity ultimately returns to that which the device was assigned to handle. Then and only then will that device begin to conduct current again, while in turn, the opposing device must now stop conducting. This "sharing of polarity" behavior leads to what is commonly termed "crossover" or "notch" distortion.
Due to the battery-like type of charge storage within them and their inherent speed limitations, the transition between opposing output devices can never be perfectly aligned in time to produce a seamless flow of electrical current. Typically, a small discontinuity or "notch" at the zero-crossing (crossover) point can always be observed by an oscilloscope connected to the output terminals of the amplifier. This notch represents distortion and is of a static nature, meaning its amplitude remains the same at all signal levels. Therefore, this distortion represents an ever-increasing percentage of the total output as power levels are reduced, and contributes to a "grainy" sound that is particularly audible and quite irritating at low listening levels.
Conversely, in Class-A operation the output device is never completely shut off, so there is no "turn on" or "turn off"" time requirement, per se. Hence, there are no issues with charge storage or any ensuing crossover distortion. Class-A designs generally offer better high frequency performance and over-all feedback loop stability. This second point is especially important because all amplifiers produce some distortion, but compared to other topologies Class-A's superior feedback loop stability means that fewer high-order distortion harmonics are generated. The result is a more natural and harmonically accurate reproduction that is significantly less fatiguing.
Single-Ended (SE) Design:
One unique advantage of Class-A design is the ability to employ only a single output device, with the technique commonly referred to as Single-Ended design. Quite simply, such a configuration guarantees that there is no opportunity for the generation of crossover distortion, and therefore is considered by many to be the purist form of amplification possible. The HA-200 operates in full SE Mode when used in its stock stereo configuration.
Furthermore, the single output transistor is operated with a rock-solid constant-current bias, which provides for very stable control over the output signal at all times. Musical waveform accuracy is maintained such that typical "overshoot" and "ringing" artifacts are virtually eliminated. The sonic effect is one of a fast and authoritative response manifesting as exceptionally accurate and natural transient reproduction at all frequencies and dynamic levels.
Balanced Headphone Mode:
Unique to the HA-200 is its ability to quadruple output power by simply adding a second unit and operating them together in "Balanced Headphone Mode." For this configuration, all that's needed is to use the XLR inputs and outputs on each HA-200 along with a special cable adaptor for connecting the headphones.
In Balanced Mode, four completely separate amps (2 per unit) are utilized to drive the four phases of the music signal (right normal, right inverted, left normal, left inverted). Please keep in mind though that this is NOT the same technique as mentioned above in the "push-pull" Class-B scenario. In Balanced Mode, all transistors are biased in Class-A so as to conduct current at all times – only the phase is inverted 180 degrees in the case of the left & right inverting amplifiers.
The primary benefit of such a design is that the available output voltage is doubled, so the actual output power is quadrupled. It also doubles the effective slew rate (the maximum change in voltage per second that an amplifier can achieve), as both amplifiers are operating in opposite phase to increase the dynamic realism of the music. While "technically" not a pure SE design, since Balanced Mode remains in full Class-A operation at all times it can be thought of as a "dual SE" architecture that retains the best of SE performance with the added benefits of higher power and better dynamic control.
Sonically, the resulting sound is completely "grain-free," the soundstage is wide and deep while instruments and voices are reproduced with extreme clarity and purity of tone. The incredible power and dynamic control over the music simply must be experienced to be appreciated.
Class-A's Modest Disadvantage:
The one slight disadvantage that Class-A amplifiers have is that transistor bias current must be set such that the output transistor continually operates in the center of its "linear region," which simply speaking is the midpoint between its fully-on and fully-off limits. Therefore, regardless of the actual audio power being used Class-A amplifiers continuously consume their full-rated output power and dissipate that power in the form of waste heat.
Now in some cases this might be a serious efficiency issue, but mostly in those applications involving loudspeaker amplifiers capable of delivering several hundred watts of power. With headphone amplifiers, this is less of a concern due to their need for significantly less output capability. Nevertheless, while in operation the HA-200 will continuously consume 24W of power. In fact, that value actually exceeds the idle power consumption of a NuForce Reference 18 amplifier! The upshot is that in order to benefit from the superlative performance that the HA-200 has to offer, one must be willing to accept its somewhat lower power efficiency. In our opinion, that's a relatively small price to pay for such a great reward, and we believe that many will agree.
Other HA-200 Features Include:
- A single output gain stage (only 1 op-amp and 1 output device in the signal path)
- A high performance Alps volume control
- XLR connectors for operating in "Balanced Headphone Mode" (see above)
- A linear power supply comprised of a custom-made toroidal transformer and extensive capacitor reserves
To be sure, the HA-200 is not a headphone amplifier for the common man or woman. Developed specifically for the devout headphone enthusiast, it's comprehensive design and pristine audio performance is reserved for those that demand nothing less than the very best.
Specificatii tehnice pentru Amplificator casti NuForce HA-200 Negru
|Link producator: https://www.nuforce.com/index.php?option=com_k2&view=item&id=678:ha-200&Itemid=2710|
Amplificator NuForce HA200, NuForce HA-200, NuForce 200
REVIEW-URI PENTRU Amplificator casti NuForce HA-200 Negru
Momentan produsul Amplificator casti NuForce HA-200 Negru nu are nici un comentariu din partea utilizatorilor. Fii tu primul care adauga un comentariu.
La AVstore.ro cumperi la preturi PROMO, poti plati in rate si ai livrare GRATUITA pentru comenzi peste 300RON in reteaua Fan Courier.
Vezi specificatii tehnice, review-uri si pareri despre Amplificator casti NuForce HA-200 Negru (H1MK9R1101E0).
Disclaimer: Echipa AVstore.ro încearcă să menţină acurateţea informaţiilor la Amplificator casti NuForce HA-200 Negru dar rareori acestea pot conţine mici inadvertenţe, ex: accesorii neincluse în preţ, specificaţii tehnice diferite, informaţii neactualizate despre preţ şi stoc. Ne poţi contacta oricând pentru a clarifica eventuale nelămuriri. Nu uita să menţionezi în corespondenţa ta numele exact al produsului - Amplificator casti NuForce HA-200 Negru